Deligreen 15S 80A 100A 48V PCM/PCB/BMS for 3.2V LiFePO4 battery pack 18650 Lithium Battery Pack protection board | Электроника

Deligreen 15S 80A 100A 48V PCM/PCB/BMS for 3.2V LiFePO4 battery pack 18650 Lithium Battery Pack protection board | Электроника

Notes: Please see table as below to find right models.

3S 10A-200A

8S 10A-200A

14S10A-200A

20S10A-200A

4S 10A-200A

10S10A-200A

15S10A-200A

21S10A-200A

6S 10A-200A

12S10A-200A

16S10A-200A

24S10A-200A

7S10A-200A

13S10A-200A

17S10A-200A

LTO BMS

About temperature monitor,If you need pls tell us

Model: DG15S 80A 100A  for 3.2V rated Li-PO LiNCM battery 

We can customize any PCB from 2S to 24S lithium batteries with different current.

Welcome retail and wholesale both. More discount for volume order!

DG15S 80A 100A  PCB is used for 15series battery pack.

We can design it for various lithium batteries like LiFepo4, LiMn2O4, and Li-polymer etc.

The main functions are: over charge protection, over discharge protection, over current protection, short-circuit protection,

temperature protection etc.

​

Content

Spec

Unit

Remarks

Discharge

constant discharge current

80/100

A

peak discharge current

220

A

charge

charge voltage

48

V

charge current

80/100（MAX）

A

Over charge protection

over charge volt

4.25±0.05

V

over charge volt protect delay

0.5

S

Over charge volt release

4.19±0.05

V

Power balancing

Power balance volt

4.18

V

balance release volt

4.18

V

balance current

35

mA

Over discharge protection

Over discharge detect  volt

2.8±0.05

V

Over discharge detect delay

0.5

S

Over discharge volt release

3.0±0.05

V

Over  current protection

Over current detect volt

150

mV

Over current detect delay

9

MS

Over current protection

80/100

A

Over current protect release

disconnect load

Short circuit protection

Short circuit protection

External load short circuit

Short circuit detect delay

250

uS

Short circuit detect release

Disconnect load

Temperature

protection

Temp protection

none

℃

Can be customized

resistance

Main circuit resistor

≤10

mΩ

Self-

consumption

Working current

≤50

uA

Sleepy current(when battery is over discharged )

≤12

uA

Working temp

temp range

-30/+80

℃

1) Which current of the PCB should i choose?  

Take 13S 48V pack as an example: Which PCB you should choose depends on the power of your motor or the current limitation of your controller. Below 350W ,you can choose 16A.Below 500W, you can choose 18A, Below 800W, you can choose 35A,Below 1KW, you can choose 60A. Above 1200W, the same. If you are not sure, please contact us freely.

2) Can I use bigger size of PCB than it should?

Suppose you need 60A PCB but you chose 80A, that is OK.

80A allows higher current.Nothing bad but a bit higher price.

But if you choose 50A, sorry it is too small. So you can choose higher spec but can’t choose lower one than it should have been.

3) What kind of charger should i choose?

Lithium battery must be charged by lithium battery charger. You can’t charge it with a lead acid battery charger. The lead acid battery charger might damage MOS pipe of the PCB.

4) If i have PCB, do i need any balancers?

Yes if you can add QNBBM balancers, that would be perfect.

The Main function of PCB is to prevent batteries from over charged or over discharged,over heated etc.

All the PCB /BMS in the world balance performance is not satisfactory.

With balancers added, the batteries lifespan will be longer and the capacity will be fully used.

5) How to judge if my PCB is broken or not ?

If you’d like to judge if the PCB is fine or not, please use a multi-meter and see if the voltage of each cell is close to each other or not.when the volt difference is 1V, the battery will have such performance:driving distance is short, cut off when started, charging time is very short.under such situation , some battery is defective. When the PCB is broken, the battery can’t be discharged when you measured the battery volt is normal.